Home page

View all product categories

News and Information

Pull ring cover

Release time:

2022/04/12

Source:

Website

Pull ring cover

Previous item

Medicine bottle cap

Next one

More information

TPE,TPR material is maturely used in bicycle and motorcycle handlebar cover

2021-01-05

TPE,TPR material is maturely used in bicycle and motorcycle handlebar cover Bicycle and motorcycle handlebars usually use a soft rubber material handlebar cover, this soft material handlebar cover has a soft feel, non-slip and other effects. This kind of soft material, the most common is soft PVC and rubber Soft PVC cost is relatively low, has a good elasticity and feel, but PVC for handlebar, there are two main defects, one is the low temperature resistance is poor, the temperature in -10 ~ -5 ℃, PVC easy to harden and gradually lose elasticity and feel; Second, most of the PVC toxic, containing halogen and toxic plasticizer phthalate, it is difficult to be competent in some high-end motorcycle bicycle handlebar cover. The rubber handlebar cover has better mechanical strength and wear resistance, long service life. But rubber needs to be vulcanized, the production cycle is long, and the material is difficult to recycle, is also a headache for users. The development of thermoplastic elastomer TPE / TPR in recent years can be described as a rapid development, in all walks of life, repeatedly show their skills, multiplied by the rubber and plastic industry attention. Its many advantages, making it an alternative to traditional PVC and rubber, handy in a variety of bicycle and motorcycle handlebar cover. TPE and TPR are thermoplastic materials, which can be injection molded quickly without vulcanization, so that the production cycle can be calculated in seconds instead of minutes for rubber. Advantage 2: Environmentally friendly material. Compared with vulcanized rubber materials, TPE/TPR can be 100% recycled and reused to protect the environment. Advantage 3: Excellent low temperature resistance. Relative to PVC, TPE/TPR low temperature resistance can be in -50 ℃ low temperature still maintain the elastic properties of the hard, still has excellent elasticity and soft touch. Advantage 4: thermoplastic rubber TPE/TPR does not contain halogen, does not contain toxic o-phenyl plasticizers, does not contain heavy metals, etc., is an excellent environmental protection materials. The following are some of our main cases of TPE/TPR used as bicycle and motorcycle handlebar cover. 1. All the materials are made of TPE/TPR, individually injection molding, hardness depends on customer requirements. 2. TPE, TPR and hard plastic cover glue bonding, hard plastic is usually PP, ABS or PA nylon. 3. There is also a more high-end bicycle handlebar cover, the use of soft TPR (such as 15 ~ 30 degrees) with hard TPR (hardness in 75 ~ 90A), soft and hard TPR material is usually used in two colors. Shangli Plastic is looking forward to your call! Contact:139 2505 9389 Mr. Yan For more information, please see: http://www.dgshangli.cn

What is the processing temperature and molding temperature of TPE

2020-12-14

What is the processing temperature and molding temperature of TPE Depends on the hardness of TPE, generally soft material 150-190 degrees Celsius, high hardness 180-240 degrees Celsius processing temperature. TPE is also known as triethyl phosphate, TPE-Triethyl phosphate state is a colorless and non-flammable liquid, slightly hygroscopic, stable at room temperature, soluble in alcohols, ethers and a variety of organic solvents, soluble in water, but decomposed with the increase in temperature, boiling point 216 degrees Celsius. It is used as chemical reagent, catalyst for production of acetic anhydride and diethylene ketone, nitrocellulose and cellulose acetate solvent, synthetic resin plasticizer, organic insecticide stabilizer, ethyl agent, chemical synthesis intermediate, lubricant additive, resin flame retardant. Shangli Plastics is looking forward to your call! Contact:139 2505 9389 Mr. Yan For more information, please see: http://www.dgshangli.cn

What to pay attention to in TPE covered ABS

2020-11-09

What to pay attention to in TPE covered ABS TPE covered ABS products have good applications in various industries. Sometimes there are some bad phenomena after the production of encapsulation out, the following analysis of TPE encapsulation ABS what problems are likely to occur? 1, the phenomenon of lack of glue. This is mostly due to the processing process, processing temperature and pressure are not high enough. So we should raise the injection temperature and increase the injection pressure. 2, the product produced by overmolding has poor adhesion. This is mainly due to the unreasonable production formula before processing, and the injection temperature is not high enough. Therefore, we should pay attention to improve the injection temperature and adjust the appropriate formula. 3, its appearance is not smooth, nor shiny. This is mainly the raw material moisture is not enough, the processing temperature is not enough to produce. Therefore, when wrapping and processing again, the injection processing temperature should be increased and the moisture of raw materials should be reduced. 4, in the manufacturing process, it will appear to stick to the mold phenomenon. At this time we add some mold release agent will be able to prevent its sticky mold. 5, the surface cleanliness of ABS products, TPE material preheating before processing, the choice of color powder or masterbatch has a certain impact on the adhesion of TPE and ABS package. Shangli Plastics is looking forward to your call! Contact:13925059389 Mr. Yan For more information, please see: http://www.dgshangli.cn http://1806260057.pool2-site.make.yun300.cn/product/11/

How to set the injection parameters of TPE material

2020-09-17

How to set the injection parameters of TPE material As a TPE manufacturer in Dongguan, the following is an introduction to the parameters of TPE injection molding to supply the friends who need to know. Because TPE material has the performance of rubber and the processing method of PVC, TPE material can be processed and molded with general injection molding grade, without special machinery and equipment, and the molding cycle is short. Rubber is hot demoulding, TPE material is cold demoulding, so the two materials are different processing methods. TPE injection molding processing parameters depend on the type of TPE, grade (formula design) and product structure and other factors, because each TPE manufacturer's material formula is different, the material shrinkage rate, circulation and so on are different, and the structure of the product, mold design have a lot to do with the specific processing parameters should refer to the material supplier's physical properties table! We are a free to customize different material formulations for customers to create a more cost-effective TPE, TPU, TPV, TPR, TPV raw materials, with unique performance, excellent quality has been recognized by the majority of customers! Shangli Plastics is looking forward to your call! Contact:139 2505 9389 Mr. Yan For more information, please see: http://www.dgshangli.cn

COOKIES

Our website uses cookies and similar technologies to personalize the advertising shown to you and to help you get the best experience on our website. For more information, see our Privacy & Cookie Policy

COOKIES

Our website uses cookies and similar technologies to personalize the advertising shown to you and to help you get the best experience on our website. For more information, see our Privacy & Cookie Policy

required

These cookies are necessary for basic functions such as payment. Standard cookies cannot be turned off and do not store any of your information.

analyze

These cookies collect information, such as how many people are using our site or which pages are popular, to help us improve the customer experience. Turning these cookies off will mean we can't collect information to improve your experience.

Feature

These cookies enable the website to provide enhanced functionality and personalization. They may be set by us or by third-party providers whose services we have added to our pages. If you do not allow these cookies, some or all of these services may not function properly.

advertise

These cookies help us understand what you are interested in so that we can show you relevant advertising on other websites. Turning these cookies off will mean we are unable to show you any personalized advertising.

Copyright © 2022 Dongguan Shangli Plastics Raw Materials Co., Ltd.

SEO | Privacy Policy